Great units
I have 2 set up for split phase. Charging and inverting work flawlessly. The UPS function is amazing. Really enjoy these units.
SKU: PMP482505120





Log in to check member price and detailed stock information.
| Need more than what's available? Tell us what you need and we can source it for you. |
The Victron MultiPlus-II 48/5000 is a 48V inverter charger that turns your battery bank into 4,000W of pure sine 120V power, with a 70A charger, a 95A transfer switch and a switchover to battery in under 20 milliseconds when the grid or generator drops. Run one on a cabin, shop or backup subpanel, or pair two for a 120/240V home, and this version carries UL 1741 for home and grid-tied systems plus UL 458 for RVs and boats.
5,000VA (4,000W) continuous at 77°F (25°C), 3,700W at 104°F (40°C), and 9,000W peak for motor starts
48V battery input (38 to 66Vdc) with a 70A adaptive charger
One 120V AC input (90 to 140Vac) with a 95A transfer switch and transfer to battery in under 20 ms
Main output for critical loads plus a second output that switches off when AC input is lost
Two units for 120/240V split phase, three for three phase, and up to six in parallel
Idle draw of 10W in AES mode and 3W in search mode, with 96% peak efficiency
Programmable relay for generator start/stop, alarms or low battery voltage
UL 1741 and UL 458 listed (Victron part PMP482505120), 71 lb (32 kg), 26.6×13.0×6.5 in (676×330×164 mm)

Current Connected is YOUR Victron product specialist
The MultiPlus-II is an inverter, a battery charger and an automatic transfer switch in one 48V unit. Wire the grid or a generator into its AC input, and it runs your loads from that source while it charges the bank. When the source drops, it carries the main output from the batteries in under 20 milliseconds. In our testing, the switchover barely registers on an oscilloscope, so computers, routers and refrigerators ride straight through.
The 48/5000 is the largest 120V MultiPlus-II Victron builds, sized for cabins, shops, backup subpanels and 48V RV or boat systems. This is Victron's PMP482505120 version, listed to UL 1741 for home and grid-tied installs and to UL 458 for vehicles and boats, so one model covers the house, the cabin and the rig on the road.
The 5,000VA rating is apparent power, so size your loads by watts: 4,000W continuous at 77°F (25°C), easing to 3,700W at 104°F (40°C). Peak output reaches 9,000W to carry the starting surge of a well pump, an air compressor or a welder, and the pure sine output serves sensitive electronics well.
When loads are light, AES mode drops idle draw to 10W and search mode to 3W. On an off-grid bank, that difference adds up overnight.
A single MultiPlus-II delivers 120V, which covers essential circuits, outbuildings and subpanels where 240V isn't needed. For a 120/240V panel that runs HVAC, a well pump, a range or a dryer, a second identical unit configured for split phase gives you 8,000W across both legs. Start with one today and add the second when your system grows, as long as it's the same model.
Want both units and the distribution in one order? The Residential 10kVA 120/240V Off-Grid Power System Kit pairs two MultiPlus-II units in split phase with a complete Lynx distribution system. For more capacity, up to six units run in parallel, and three units make three phase (wye only, not delta).
PowerControl sets a current limit on the AC input, so a generator or a 30A circuit never gets asked for more than it can give, and the charger takes whatever your loads leave over. PowerAssist works the other way: when loads climb past that limit, the MultiPlus-II adds battery power on top of the incoming AC, so a modest generator handles peaks well beyond its rating, then refills the bank once demand drops.
Victron's optional external current sensor extends PowerControl and PowerAssist to 100A.
The MultiPlus-II takes one AC source. If your system sees only the grid, or only a generator, that's all you need. If you want the grid and a generator both wired in, with the inverter choosing between them, the Quattro 48/5000 pairs the same 4,000W inverter and 70A charger with two AC inputs at 100A each and saves you an external transfer switch.
The main output keeps critical loads running on every source. The second output stays live only while AC is present, so a water heater or other heavy load drops off during an outage instead of draining the batteries. It reconnects about two minutes after AC returns, which gives a generator time to settle.
A built-in ground relay bonds neutral to ground while the MultiPlus-II is inverting and opens before the AC input connects, so the system keeps one neutral-ground bond whichever source is running.
Victron recommends a 200 to 800Ah battery bank at 48V for this model, roughly 10 to 40kWh of storage. Our team is happy to help with sizing.
The battery side lands on two M8 bolts, torqued to 12 Nm (106 in-lb). Victron specifies one 2/0 AWG cable per terminal for runs up to 16 ft (5 m) and 4/0 AWG from 16 to 33 ft (5 to 10 m), in 90°C (194°F) copper kept out of closed conduit. Our custom battery cable builder makes both cables to your exact length with the lugs you pick for each end.
Victron calls for a 200A DC fuse on the battery feed. On a Lynx Distributor or fused busbar, a 200A Littelfuse MEGA fuse covers each MultiPlus-II branch, with a Class-T fuse at the battery as main protection.
On the AC side, the input takes a breaker of 95A or less on at least 4 AWG wire, and the main output a 115A breaker on at least 2 AWG, with UL 943 ground-fault protection in series. Mount the unit in a dry, well-ventilated spot as close to the batteries as practical, and give paralleled units 4 in (10 cm) of open space all around.
Programming runs through an MK3-USB interface (sold separately) and VictronConnect on a laptop, where you set the charge profile, input current limit, PowerAssist and relay behavior. Program the charger for your battery before the first charge.
Add a Cerbo GX or Ekrano GX to watch and adjust the whole system from anywhere on Victron's free VRM portal.
Victron sells three versions of the MultiPlus-II 48/5000/70-95 120V. PMP482505110 is the standard model, PMP482505120 adds the UL 1741 and UL 458 listings, and PMP482505300 is a 50/60Hz version. We stock the PMP482505120. For an inspected install or one that needs utility sign-off, the UL 1741 listing is the one to have.
The AC input current limit is set below what your circuit can supply, so PowerAssist starts leaning on the batteries early. One customer saw the batteries take over everything above about 2,000W for exactly this reason. Set the input current limit in VictronConnect to match your breaker or generator, and the grid or generator carries more of the load.
Yes. A grid-tie PV inverter on the MultiPlus-II's output can run loads and charge the bank, and when the batteries are full the MultiPlus-II raises its output frequency to throttle the PV inverter back. The PV inverter has to support frequency shifting. Victron's Factor 1.0 rule caps AC-coupled PV at the inverter charger's VA rating, so up to 5,000W here, and its AC coupling guide calls for roughly 4.8kWh of lithium storage for every 1.5kW of PV. DC-coupled solar through a SmartSolar MPPT charge controller charges the bank directly and falls outside the Factor 1.0 rule.
Yes. Victron supports lithium banks that have a BMS monitoring and controlling the cells, and its guide, Connecting other lithium battery systems to Multis and Quattros, covers which batteries work and how to set each one up. Batteries that talk over CAN-bus connect to the system through a GX device.
No. Victron doesn't supply the temperature sensor with 48V models, so add one if you charge lead-acid batteries and want temperature-compensated charging. On a lithium bank, the BMS normally handles temperature protection.
No. Once it's programmed, the MultiPlus-II runs on its own. A GX device earns its place when you want ESS or a CAN-bus link to a smart lithium battery.
It can run grid-interactive as part of a Victron ESS and carries a UL 1741 listing, but export is up to your utility. Get interconnection approval before you set the system to feed back, and check with your AHJ (Authority Having Jurisdiction).

Victron 5kVA 48V MultiPlus-II - Breakthrough Technology?

Victron Split Phase Configuration Guide
I have 2 set up for split phase. Charging and inverting work flawlessly. The UPS function is amazing. Really enjoy these units.
Everything works perfect, except load assist. Running under 2,000 watts it pulls 2,000 watts from grid to run things and charge the batteries. Anything over 2k lowers the grid draw and drains the batteries.
Thank you for the feedback! This can be changed in programming by adjusting the input current limit. Our team is happy to assist if you would like to call / email us!