IntegraRack IR EarthBallast Solar Panel Ballast Mounting System for BallastRack Ground Mounts, Geotextile and Epoxy Kit, No Concrete or Ground Penetration
SKU: IR-RFEB1071




Log in to check member price and detailed stock information.
| Need more than what's available? Tell us what you need and we can source it for you. |
Product Summary
The IntegraRack IR EarthBallast kit anchors a row of BallastRack ground mount frames with soil or crushed rock instead of concrete footings or ground screws. You epoxy a heavy geotextile sheet across the base tubes, pull it tight and pile ballast on top, so the array goes in with no digging, drilling or concrete.
Specifications:
-
One 3 × 50 ft section of heavy-duty geotextile, enough for a row of up to 12 panels with 2 ft extra past each end
-
Dual cartridge high-strength epoxy and a dual cartridge caulk gun, plus a spare mixing nozzle, scuff pad, two alcohol wipes and a 13 mm ratchet wrench
-
Fits every IntegraRack BallastRack frame, including the IR-15, IR-30, IR-40FSA and IR-45ASA
-
Takes about 1,000 lb of compactable soil or crushed rock per panel, with each frame's stamped datasheet setting the exact weight
-
Leaves about a 2 in air gap under the ballast once the fabric is pulled tight across the base tubes
-
Two 3/4 × 12 in round steel forming stakes per frame recommended (not included)
-
Uses standard 1 in EMT conduit (not included) or IntegraRack composite base tubes (sold separately) to link the frames
-
Apply and store the epoxy at 40°F or warmer

Current Connected is YOUR IntegraRack product specialist
This product is currently unavailable. Consider one of these alternatives.
About the IntegraRack IR EarthBallast Solar Panel Ballast Mounting System
EarthBallast turns the ground you're building on into the anchor. A geotextile sheet epoxied to every frame's base tube carries a mound of soil or crushed rock, and that weight holds the array down without concrete footings, ground screws or post pounding. It's the anchor to reach for on rocky ground where screws won't drive, and on sites where you want the array to stay movable.
How the Geotextile Soil Ballast Goes Together
Set and level the frames first, linked with 1 in EMT conduit or IntegraRack composite base tubes. Scuff and wipe each base tube, run a bead of the 15-minute epoxy from the included caulk gun, then roll the geotextile along the row and pull it tight across the tubes so it sits like a trampoline with about 2 in of air underneath. Leave 2 ft of fabric past each end of the row, then mound the ballast toward the rear, no more than 12 in from the tall leg. Two 3/4 × 12 in steel forming stakes per frame add strength and make leveling easier.
How Much Soil Ballast Per Panel
Plan on about 1,000 lb of compactable soil or crushed rock per panel, with each frame's stamped datasheet listing the exact figure for its angle and panel size. The IR-45ASA datasheet, for example, calls for 1,000 lb with 22 in of fill. For bifacial panels, light-colored crushed rock bounces more light onto the back of the panels.
IntegraRack rates one kit for a row of up to 12 panels. Our support team is happy to work out kits and ballast for your row.
Ground Mount Solar Without Concrete or a Building Permit
IntegraRack treats BallastRack frames ballasted to its datasheets as temporary, movable structures, and states that arrays under 5 ft 9 in (1,753 mm) tall fall under the IBC Chapter 1, Section 105.2 building permit exemption. Requirements vary by county, so confirm with your AHJ (Authority Having Jurisdiction) before you build.
Need the most wind headroom? Bolting to a slab with the SlabBallast kit gives the highest ratings of any BallastRack anchor.
Recommended Accessories
Frequently Asked Questions
IntegraRack's install instructions call for compactable soil, since loose soil or sand can shift in high winds. Road base and crushed rock pack down well, and light-colored crushed rock adds bifacial gain.
Yes. IntegraRack pairs the two by setting BladderBallast bladders on the geotextile between frame sections, each holding up to 875 lb of water when full. Treated 2x4 lumber spanning the base tubes is another option IntegraRack lists for carrying the load.
The ground needs to be mostly level. IntegraRack's BallastRack instructions cap the slope at 10% north to south and 5% east to west, and a 6 in pad of compactable road base about 4.5 to 5 ft wide along the row is an option for leveling.
Customer Reviews
No reviews yet. Be the first to review this product!











